Home » Impression Materials » Industrial Impression Materials

Industrial Impression Materials

Our Industrial Impression Materials are high consistency, addition-curing, moldable, silicone compounds. These materials are compounded for taking primary impressions. The IIM line of products is NOT to be used for taking impressions in the mouth or of the skin. The I.I.M.material has NOT been FDA approved for use in the mouth or on the skin. Casual skin contact is permitted.

Typical Properties

Mixing Ratio	1:1
Mixing time (min.)	0:45
Working time (min.)	1:30
After the mix
Recommended set time (min.)	5:30
% Strain in compression	2.2
% Linear shrinkage after 24h.	0.1
% Compression set	0.7
% Elongation @ break	not determined
% Recovery from Deformation	99.3
Hardness Shore A after 24 hours	*Denoted by Product # IIM(S or L)XXXX-21, -32, -36, -40 (- # Denotes Hardness)

The times and properties are valid at room temperature and relative humidity.

Product Use Information

The catalyst component contains an active metal complex.

Use equal parts of Base and Catalyst by weight or volume at room temperature and Relative Humidity. Higher temperatures shorten work and cure times, while lower temperatures prolong work and cure times.

**IMPORTANT** Only the Base and Catalyst with the same lot and product number should be kneaded together until the color is homogeneous.

Storage and Shelf-Life

Should not be used after the expiration date. Store at = 78 ºF and away from sunlight.

Safety and Handling

For specific information regarding safe handling of this material, please refer to the Material Safety Data Sheet. Keep away from children. This material should NOT be used for skin or dental impression purposes. Federal law prohibits the use of this material for purposes other than intended.

Packaging

Refill
2 jars, Base (250 g) & Catalyst (250 g)	PRODUCT # IIMS-35, IIMS-40, IIML-20, IIML-30
2 jars, Base (500 g) & Catalyst (500 g)	PRODUCT # IIMS-35, IIMS-40, IIML-20, IIML-30
Single Base (15 g) & Catalyst (15 g)	PRODUCT # IIMS-35, IIMS-40, IIML-20, IIML-30
	*EXXXX- # (- # Denotes Hardness)
Economy
8 jars, 4 Base (250 g) & 4 Catalyst (250 g)	PRODUCT # IIMSE-35, IIMSE-40, IIMLE-20, EIIMLE-30
8 jars, 4 Base (500 g) & 4 Catalyst (500 g)	PRODUCT # IIMSE-35, IIMSE-40, IIMLE-20, IIMLE-30
100 Singles, 50 Base (15 g) & 50 Catalyst (15 g)	PRODUCT # IIMSE-35, IIMSE-40, IIMLE-20, IIMLE-30
	*EXXXXE-XX (E denotes Economy)
Bulk (B)
50 lbs & Over	PRODUCT # BIIMSE-35, BIIMSE-35, BIIMSE-35, BIIMSE-35 BIIMLE-35, BIIMLE-35, BIIMLE-35, BIIMLE-35

Caution:

• Store at room temperature, 65O - 75O F (18O - 24O C).
• Wash your hands before handling this material.
• Do not wear latex gloves when handling this material.
• Do not use hand lotion before mixing this product.
• Keep this material out of children.
• Do not swallow or take internally.
• Do not take impressions of the skin with this material (casual contact is permitted)
• Do not use this material in the mouth.

Northeast Resins & Silicones, LLC assumes no liability for intentional or unintentional misuse of this product.